woodsy Posted April 24, 2022 Report Share Posted April 24, 2022 i'm despairingly trying to get wobbler up and running before spending the next week trying to figure out the lamps etc... god knows how @wearecity does it so easily!! just baffles me!! anyways i don't know what this error is and how to get around it so i can get into test mode for starters.. if anyone has the answer please share, if anyone wants to map the lamps for me while i do the art please form a queue haha living the dream Link to comment Share on other sites More sharing options...
WonkySausage Posted April 24, 2022 Report Share Posted April 24, 2022 (edited) Not sure if this is the same error message, but sometimes, when i'd downloaded an MPU5 game from the legacy section. In the cofing settings, it would have service and cash door with the number 0 in it. And when you tried opening said doors, it would give you this error message. Basically, long winded way of saying - make sure Service and Cash door numbers aren't set to 0 in the config settings window, and the correct numbers are there. Once you've put the correct numbers in you'll probably have to RAM clear. Edited April 24, 2022 by WonkySausage Link to comment Share on other sites More sharing options...
wearecity Posted April 24, 2022 Report Share Posted April 24, 2022 The answer is.............. Change the hopper type to serial. 2 Link to comment Share on other sites More sharing options...
woodsy Posted April 24, 2022 Author Report Share Posted April 24, 2022 20 minutes ago, wearecity said: The answer is.............. Change the hopper type to serial. still not helping i'm afraid... arghhhhh living the dream Link to comment Share on other sites More sharing options...
woodsy Posted April 24, 2022 Author Report Share Posted April 24, 2022 (edited) its like wonky says.. it boots fine and works in door closed mode but it goes into error when s door gets ticked. if anyone can sort this so it can get into test mode and i can lamp it etc thanks WOBBLER error 90-4d.zip Edited April 24, 2022 by woodsy living the dream Link to comment Share on other sites More sharing options...
Matty.n Posted April 24, 2022 Report Share Posted April 24, 2022 Funnily enough i'd been playing about with this earlier @PekoJPF's request! I did have a similar issue with another MPU5 machine before so will do some digging & try to find the solution. Link to comment Share on other sites More sharing options...
wearecity Posted April 24, 2022 Report Share Posted April 24, 2022 It seems to be very sensitive to wrong button presses. I have it to asking to read meters with the following set up. Button 32 is start Link to comment Share on other sites More sharing options...
Matty.n Posted April 24, 2022 Report Share Posted April 24, 2022 Well, the solution for my issue was the hopper being serial, works fine in open/closed door for me. Using buttons 32 - 39 for Start/Hold/Collect etc 1 Link to comment Share on other sites More sharing options...
Matty.n Posted April 24, 2022 Report Share Posted April 24, 2022 57 minutes ago, wearecity said: The answer is.............. Change the hopper type to serial. Thanks for this, I remember struggling for so long with another machine & was saying to @PekoJPF I'm sure it was something triggering a hopper input option, serial hopper completely evaded my thought process! Link to comment Share on other sites More sharing options...
woodsy Posted April 24, 2022 Author Report Share Posted April 24, 2022 3 minutes ago, wearecity said: It seems to be very sensitive to wrong button presses. I have it to asking to read meters with the following set up. Button 32 is start 2 minutes ago, Matty.n said: Well, the solution for my issue was the hopper being serial, works fine in open/closed door for me. Using buttons 32 - 39 for Start/Hold/Collect etc very much obliged to you guys.. behind every one of my dx's is a much more informed and knowledgable classic creator!! that's why this ones kicking me about a bit haha.. living the dream Link to comment Share on other sites More sharing options...
woodsy Posted April 24, 2022 Author Report Share Posted April 24, 2022 ok neither of those setups are working for me.. please can you post your versions and that will at least give me achance... living the dream Link to comment Share on other sites More sharing options...
Matty.n Posted April 24, 2022 Report Share Posted April 24, 2022 3 minutes ago, woodsy said: ok neither of those setups are working for me.. please can you post your versions and that will at least give me achance... Throw a Wobbler (barcrest).zip Link to comment Share on other sites More sharing options...
woodsy Posted April 24, 2022 Author Report Share Posted April 24, 2022 (edited) it appears wobb_5s.bin is the problematic part of this saga.. THANKS to both of you for saving me the hassle of buying a new laptop after throwing this one at the fekking wall haha any ideas how i get this into test mode.. as i'm about to give up for the day hah Edited April 24, 2022 by woodsy living the dream Link to comment Share on other sites More sharing options...
Matty.n Posted April 24, 2022 Report Share Posted April 24, 2022 4 minutes ago, woodsy said: it appears wobb_5s.bin is the problematic part of this saga.. THANKS to both of you for saving me the hassle of buying a new laptop after throwing this one at the fekking wall haha any ideas how i get this into test mode.. as i'm about to give up for the day hah Other MPU5's are let it boot in open door, at read meters press cancel then press Test, this doesn't seem to be having it so probably a non standard number, i'm slowly getting through the list! 1 Link to comment Share on other sites More sharing options...
slotsmagic Posted April 24, 2022 Report Share Posted April 24, 2022 (edited) 6 minutes ago, Matty.n said: Other MPU5's are let it boot in open door, at read meters press cancel then press Test, this doesn't seem to be having it so probably a non standard number, i'm slowly getting through the list! Don't forget this era of MPU5 will probably have 2 test buttons - one on the MPU5 and one mounted under the reel shelf. You need to hold one and press the other to enter test mode - wasn't sure if you were aware based on your post Trying to remember how I do it, I think I set the standard test button number (should be standard as it's on the MPU5 itself) with a keyboard shortcut and then click the other buttons? Edited April 24, 2022 by slotsmagic 1 Currently owned digitals : T7 Encore, T7 Original, Astra iPub and Storm Street Casino. MFME cabinets : Genesis cab DIY by No1Stoney, Interplay conversion and Vegas Strip conversion (both are works in progress!) Link to comment Share on other sites More sharing options...
WonkySausage Posted April 24, 2022 Report Share Posted April 24, 2022 was gonna say in my original post that it was probably way deeper than it just being the door numbers in the config screen haha, so far that's been the only time i've ever encountered the error message myself all the stuff here is good to know for future reference though Link to comment Share on other sites More sharing options...
woodsy Posted April 24, 2022 Author Report Share Posted April 24, 2022 5 minutes ago, Matty.n said: Other MPU5's are let it boot in open door, at read meters press cancel then press Test, this doesn't seem to be having it so probably a non standard number, i'm slowly getting through the list! I know I said I was giving up for the night but I was straight to the phone for a update check!! Will be all night, thanks for your efforts living the dream Link to comment Share on other sites More sharing options...
woodsy Posted April 24, 2022 Author Report Share Posted April 24, 2022 Just now, slotsmagic said: Don't forget this era of MPU5 will probably have 2 test buttons - one on the MPU5 and one mounted under the reel shelf. You need to hold one and press the other to enter test mode - wasn't sure if you were aware based on your post Shall we have a group rendezvous point for mpu5 test button meet ups? Somewhere hallway haha living the dream Link to comment Share on other sites More sharing options...
woodsy Posted April 24, 2022 Author Report Share Posted April 24, 2022 In fact @Clo06 helped me before with this but making one button the test button and pressing that with the s door bud at the same time, sorry to pass the Buck again living the dream Link to comment Share on other sites More sharing options...
Matty.n Posted April 24, 2022 Report Share Posted April 24, 2022 (edited) 9 minutes ago, slotsmagic said: Don't forget this era of MPU5 will probably have 2 test buttons - one on the MPU5 and one mounted under the reel shelf. You need to hold one and press the other to enter test mode - wasn't sure if you were aware based on your post Yeah, it's caught me out before, I know Reflex have a similar design. Only luck i've had is holding the Test 2 button (24) & pressing start, it clicks as if it's going into test then just goes into normal demo mode, if i hold the other test button as well then press start i get the dreaded "Unused input" alarm on button 0. Edited April 24, 2022 by Matty.n 1 Link to comment Share on other sites More sharing options...
woodsy Posted April 24, 2022 Author Report Share Posted April 24, 2022 Honestly You are saving me sone real pain here, winds me right up and I can’t cope haha living the dream Link to comment Share on other sites More sharing options...
Matty.n Posted April 24, 2022 Report Share Posted April 24, 2022 Found it! Start in door open mode, wait for the read meters screen then hold down Button 8 then press the TEST button on the MFME menu & voila! 2 1 Link to comment Share on other sites More sharing options...
woodsy Posted April 24, 2022 Author Report Share Posted April 24, 2022 Give that man a medal of honour!! It was a brave fight you took on and won!! Top man living the dream Link to comment Share on other sites More sharing options...
wearecity Posted April 25, 2022 Report Share Posted April 25, 2022 I must say, I'd just come back home, after two 12 hour shifts this weekend and knew that while progress was being made, other hurdles, were still going to be faced, to get this in test mode etc... as it was really sensitive to the slightest wrong set up. But I'd had enough screwing around with it lol. So I'm pleased to wake up and see that it's been sorted now. 1 Link to comment Share on other sites More sharing options...
woodsy Posted April 25, 2022 Author Report Share Posted April 25, 2022 1 hour ago, wearecity said: I must say, I'd just come back home, after two 12 hour shifts this weekend and knew that while progress was being made, other hurdles, were still going to be faced, to get this in test mode etc... as it was really sensitive to the slightest wrong set up. But I'd had enough screwing around with it lol. So I'm pleased to wake up and see that it's been sorted now. I’ve done no shifts or anything harder than mild gardening!! I just couldn’t cope haha at least you had a fair excuse!! But yes it’s fantastic work and thanks to you and @Matty.n for your swift help, perhaps you can be known as the 777th emergency service hahah living the dream Link to comment Share on other sites More sharing options...
Recommended Posts